---
title: "Spray Foam Cost In Kansas And Oklahoma: 2026 Budget Guide"
description: "Spray foam cost has no citable installed price in Kansas or Oklahoma. The real drivers: board feet, foam type, thermal barrier, and the 2006 energy code."
url: "https://bahlfireproofing.com/spray-foam-cost-kansas-oklahoma/"
---

[Home](/) [Blog](/blog/)

Field notes and code guides

# Spray Foam Cost in Kansas and Oklahoma: A 2026 Budget Guide

- [Ross Bahl](https://bahlfireproofing.com/author/rossbahl/)
- October 7, 2026
- 10:00 am

Spray foam cost in kansas and oklahoma: a 2026 budget guide 2

Owners in Wichita, Tulsa, and Oklahoma City ask the same first question about spray foam cost, and it is the wrong one. This article explains why no citable installed price exists for this market, what actually moves a commercial insulation number, and how to make three bidders describe the same building, covering board feet, foam selection, the thermal barrier, and the adopted energy code.

**TLDR:** There is no citable, primary, regional installed price for commercial spray foam cost in Kansas or Oklahoma, and every per-square-foot figure in circulation traces to a lead-generation site. A price per square foot is the least useful number on a bid, because two bids on the same building usually differ by scope rather than by unit price. Scope is decided before anyone prices material.

---

An owner outside Wichita took the low bid on a 40,000 square foot warehouse retrofit. The scope sheet ran to one page. The foam went up in four days. Then the inspector asked where the thermal barrier was, and nobody had carried one.

Half-inch gypsum board over 40,000 square feet of deck and wall, hung after the foam, in a building the tenant had already reoccupied. That is a drywall trade, a lift crew, and a schedule nobody planned, and everything saved on the foam went into fixing it. That sequence is not rare. Owners compare bids on a price per square foot, and that number says almost nothing about what a bidder will do.

## Why There Is No Published Spray Foam Cost Per Square Foot in Kansas or Oklahoma

Because no primary source publishes one. Every dollar-per-square-foot and dollar-per-board-foot figure circulating for commercial work traces to a consumer lead-generation site: Angi, HomeAdvisor, HomeGuide, or Modernize. Those are referral platforms, not price surveys, and their figures are residential and unsourced.

RSMeans gets offered as the serious alternative. It is not a primary source either. It is a subscription product from a commercial vendor, its unit costs are national figures adjusted by city index factors rather than measured regional bids, and nobody outside a paid seat can check them. No federal or state series publishes an installed spray foam cost for either state.

So I am not going to hand you a number, and be careful with anyone who does. What matters is which decisions move the money before a price book opens.

## Board Feet, Not Square Feet: The Unit That Actually Prices the Job

A board foot is one square foot of surface at one inch of thickness. Foam is yielded, ordered, and priced in board feet, because thickness is the multiplier. Ten thousand square feet at 2 inches is 20,000 board feet. The same area at 3.5 inches is 35,000. Seventy-five percent more material and labor, and the square footage never changed.

Two bids quoted per square foot at different thicknesses are not comparable, and neither bidder has to hide a thing for the comparison to be worthless. If the thickness is not stated on both, you are comparing two different buildings.

Here is the version that decides real money. Say the target is R-20 in the assembly. The ASTM environmental product declaration for closed-cell spray polyurethane foam, published November 11, 2024, gives an aged R-value of 6.2 to 7.0 per inch. The companion declaration for open-cell gives 3.6 to 4.5. Take the middle of each. Closed-cell at about 6.5 per inch reaches R-20 in roughly 3.1 inches, open-cell at about 3.7 per inch in roughly 5.4. Same assembly, same R, about 74 percent more board feet on the open-cell path.

That arithmetic compares scope, and it is not a design method. R per inch is not constant with thickness, so the real figure comes from the manufacturer’s published aged R at the installed thickness, and the required R from the table your building official enforces.

## The Bids That Look Cheap: What Twenty Years of Them Have in Common

I have been quoting and applying spray foam across Texas, Kansas, and Oklahoma for more than twenty years, and the bid spreads that alarm owners are almost never about margin. What people think separates a high bid from a low bid is markup. What actually separates them is two lines nobody put on the comparison sheet: the installed thickness, and whether the thermal barrier is in the number.

The common version looks like this. Two bids arrive on the same metal building about 40 percent apart. The low one carries 2 inches of closed-cell, the high one carries 3. Divide each by the board feet it represents and they land within a few points of each other. Neither contractor did anything wrong. Taking the low number without changing the spec buys two-thirds of the insulation the owner thought he was getting.

The second version is the story at the top of this article. The low bid is low because the barrier is not in it, usually sitting in an exclusion list as three words: barrier by others. That is a real trade with real square footage, and moving it off the bid does not make it go away.

The third is prep. The low bid assumes the deck arrives clean, dry, and at temperature. On a retrofit it rarely does, so cleaning, masking, and waiting on substrate temperature become change orders after the crew is mobilized.

## Closed-Cell or Open-Cell Changes Spray Foam Cost Before Any Other Decision

Foam selection is the second largest lever after thickness, and it does not work the way budget conversations assume. Closed-cell costs more per board foot but needs fewer inches for the same R, so the cheaper foam is not automatically the cheaper job.

Factor Closed-cell spray foam Open-cell spray foam

Aged R-value per inch (ASTM EPD) 6.2 to 7.0 3.6 to 4.5

Density 1.5 to 2.4 pounds per cubic foot much lower than closed-cell

Inches, and board feet per square foot, to reach R-20 about 3.1 about 5.4

Material volume for the same R baseline about 74 percent more

Vapor behavior Class II vapor retarder at roughly 1.5 inches, product specific not a vapor retarder of any class at 1 inch

Behavior in bulk water does not absorb liquid water absorbs and holds water

Thermal barrier obligation applies applies

Two rows change the answer more than any price row does. The vapor row often settles a metal building before cost enters the conversation, because the panel is already impermeable outboard. And the last row is the one owners skip: the barrier obligation does not change with foam type.

## The Thermal Barrier Is a Separate Line Item, and It Is Where Budgets Break

Section 2603.4 of the 2021 International Building Code requires foam plastic to be separated from the building interior by an approved thermal barrier. The prescriptive routes are half-inch gypsum wallboard, heavy timber per Section 602.4, or a material meeting NFPA 275. Exceptions live at 2603.4.1, and attics and crawl spaces run through the ignition barrier at 2603.4.1.6.

Two things get confused here, and both cost money. The first is a section. Section 2603.3 is the surface burning provision, limiting foam plastic to a flame spread index of not more than 75 and a smoke-developed index of not more than 450 when tested to the [ASTM E84 surface burning characteristics test](https://store.astm.org/e0084-26a.html), in the maximum thickness intended for use. Section 2603.4 is the separation provision, a physical layer somebody buys and installs. Passing 2603.3 does not satisfy 2603.4.

The second confusion is an edition. The phrase still used on job sites is the fifteen-minute thermal barrier, which came out of the 2006 through 2012 IBC. That is legacy wording. The current route is the three options above, and the assessment belongs to the licensed architect or engineer of record. Confirm the adopted edition with the authority having jurisdiction.

On many commercial jobs the barrier is a different trade on a different line, and the insulation bid legitimately excludes it. Price it when you price the foam, or the number you approved is not the number you pay.

## Kansas and Oklahoma Both Run a 2006 Energy Code, and That Sets the Thickness

Kansas names the 2006 IECC as the state standard for new commercial and industrial structures under K.S.A. 66-1227. Kansas is also a home-rule state, so adoption and enforcement of building energy codes sit with local jurisdictions rather than with the state. Oklahoma’s adopted commercial standard is the 2006 IECC together with ANSI/ASHRAE/IES Standard 90.1-2003, effective September 14, 2022, with state amendments. Read that date again: a 2022 effective date on a 2006 edition. The [DOE Building Energy Codes Program](https://www.energycodes.gov/) tracks what each state has adopted.

Both states run editions written twenty years ago, so the prescriptive insulation a code minimum buys in Wichita or Tulsa is thinner than most owners assume. A bidder who writes “meets code” can be entirely correct and still be quoting less foam than the same building would get in a city on a current edition. So decide on purpose whether you are buying compliance or performance, because the envelope a current edition produces has to go in your own scope. No inspector in either state will ask for it.

Now the trap that catches people locally. Wichita is on the 2024 IBC for building code while the energy side of the same project runs against a 2006 IECC reference. Both are true at once, and an owner who assumes the energy code tracks the building code will spec the wrong thickness. Because Kansas is home rule, that answer is jurisdiction by jurisdiction, so Wichita is not Olathe or Salina. The first call on a Kansas project goes to the building official.

Then the zones, which change the table row inside whichever edition applies. Wichita sits in Climate Zone 4A, Oklahoma City and Tulsa in Zone 3A, and a Zone 4 assembly asks more than a Zone 3 assembly in the same table, so an identical metal building costs more to insulate in Wichita than in Tulsa. Confirm the county against the climate zone table in the adopted edition, not a map graphic.

If you do spec above the minimum, spec it from a named table. The 2021 IECC insulation component R-value method at Table C402.1.3 asks R-19 plus R-11 in a liner system for metal building roofs in Climate Zones 2, 3, and 4, and R-13 plus R-6.5 continuous for metal building above-grade walls in Zones 2 and 3, rising to R-13 plus R-13 continuous in Zone 4. Neither state enforces that edition statewide, so treat those as a voluntary target. Each row is a cavity value plus a continuous value, and quoting half of one describes a wall that does not comply.

## Twelve Spray Foam Cost Drivers and What to Ask Each Bidder

Every item below is settled before anyone prices material. Put the twelve on one sheet, send it to all three bidders, and the bids come back comparable.

Cost driver Why it moves the price What to ask the bidder

Installed thickness Board feet equal square feet times inches What thickness, and what aged R is published at it?

Foam type and product Closed-cell costs more per board foot, needs fewer inches Which product, and is that the aged R at that thickness?

Thermal barrier IBC 2603.4 separation is often a separate trade Is the barrier in your number, and by which route?

Substrate condition and prep Oil, dust, rust, and moisture kill adhesion What prep is in scope if the deck is not clean and dry?

Substrate temperature Application has a temperature window What surface temperature, and who heats the space?

Access and reach height Lifts and repositioning consume hours, not material What lift equipment, and how many moves?

Occupied-building sequencing Night work, HVAC isolation, containment, re-entry Normal or off hours, and what re-entry time applies?

Removal of existing insulation Demolition and disposal are separate labor Is removal included, and the rate for wet material?

Concealed existing conditions Rust and leaks surface only after demolition Where does base scope stop and a change order start?

Mobilization and job size Rig, hose, and travel cost the same on a small job Is mobilization its own line, and a second one?

Air sealing and detailing Eaves and terminations are labor, not area Which penetrations and terminations are included?

Thickness verification Measured thickness and daily logs take crew time How is installed thickness documented?

Three answers should stop you cold. “We spray to code,” with no edition named, means the bidder has not read the table your official enforces. “Thickness as required” means a change order waiting to happen. And “barrier by others” means the barrier is your problem, at your price.

Two rows deserve more than a cell. Mobilization does not scale down: rig, hose, and travel cost about the same on 3,000 square feet as on 30,000, so a rural shop always looks expensive per square foot next to a metro building. That is arithmetic, not markup. And on a retrofit, what the old insulation hid decides the job, because foaming over an active roof leak seals water into the assembly.

## Material Prices Are the Only Spray Foam Cost Data Anyone Can Actually Cite

Two public federal price series touch this work, and both measure material leaving the factory rather than installed work. Bureau of Labor Statistics Producer Price Index series PCU326150326150, urethane and other foam product manufacturing, stood at 199.424 in July 2026 against a December 2003 base of 100, released August 13, 2026. Series WPU1392, insulation materials, stood at 289.366 in June 2026 against a 1982 base of 100.

Read those carefully, because the temptation is to turn them into a quote. The first says producer prices for that category have roughly doubled since the end of 2003. Neither series is spray-foam specific or regional, and neither includes labor, equipment, mobilization, prep, or the barrier. They are not an installed price and cannot be converted into one.

What they are good for is direction. Budgeting twelve months out, the [Producer Price Index program at the Bureau of Labor Statistics](https://www.bls.gov/ppi/) tells you whether the material side is drifting up, flat, or easing, from a dated federal series rather than a number typed into a blog.

## How to Read Three Spray Foam Bids Side by Side

This is the sequence we use, and it costs an afternoon.

1. **Write one scope sheet before requesting pricing.** Name the assemblies, the target R or thickness, the product class, and who carries the barrier.
1. **Convert every bid to board feet.** Square feet times inches, then divide the bid by that. Two bids that looked 40 percent apart usually collapse to a few points.
1. **Find the thermal barrier on every bid,** as a line or in the exclusions. If it is in neither, ask in writing.
1. **Check that the quoted R-value is the aged value at the installed thickness,** not a per-inch figure multiplied out.
1. **Confirm the code edition, climate zone, and assembly row each bidder used,** then check it with the building official.
1. **Break mobilization, prep, removal, and disposal onto their own lines,** and get the change-order rate for concealed conditions in writing.

Bids that survive those six steps are comparable. Bids that do not were never priced on the same building.

## Related Reading

- [Spray Foam Insulation Cost: What Drives the Price](https://bahlfireproofing.com/spray-foam-insulation-cost-what-drive-price/) works the same drivers from a Texas angle.
- [Closed-Cell vs. Open-Cell Spray Foam for Commercial Buildings](https://bahlfireproofing.com/closed-cell-vs-open-cell-spray-foam-for-commercial-buildings-which-one-does-your-project-actually-need/) goes deeper on foam selection.
- [When Does Spray Foam Need a Thermal Barrier?](https://bahlfireproofing.com/when-does-spray-foam-need-a-thermal-barrier/) covers the separation requirement that breaks budgets.

## Frequently Asked Questions

**How much does spray foam insulation cost per square foot in Kansas?** No primary source publishes an installed figure for commercial work in Kansas, and any range you find traces to a lead-generation site or a subscription cost book. Price turns on thickness, foam type, prep, access, and whether the thermal barrier is included. Get a project-specific bid with those broken out.

**Is spray foam more expensive in Oklahoma than in Texas?** No citable dataset answers that, so anyone saying yes or no is guessing. What is verifiable is that the codes differ. Oklahoma’s commercial standard is the 2006 IECC with Standard 90.1-2003 while Texas enforces the 2015 IECC statewide, so a code minimum is not the same spec in both states.

**What is a board foot, and why do contractors price in them?** A board foot is one square foot of surface at one inch of thickness. Foam yield, ordering, and labor scale with thickness, so board feet describe the job and square feet do not. Ten thousand square feet at 2 inches is 20,000 board feet; at 3.5 inches, 35,000.

**Is the thermal barrier included in a spray foam bid?** Often not, and that is legitimate rather than deceptive. Section 2603.4 of the 2021 IBC requires foam plastic to be separated from the interior by an approved thermal barrier, and on many jobs that is a different trade. Find it on the bid or in the exclusions, and price it alongside the foam.

**Does climate zone change spray foam cost?** Yes, through the table row rather than the rate. Wichita is Climate Zone 4A while Oklahoma City and Tulsa are Zone 3A, and a Zone 4 assembly asks more insulation than Zone 3 in the same edition. The same building at the same rate costs more in Wichita.

**Why did two bids on the same building come in 40 percent apart?** Almost always because they carry different thicknesses, or one excludes the barrier or the prep. Convert both to board feet and compare again.

## Key Takeaways

**The unit is board feet, not square feet.**

- A board foot is one square foot at one inch, and thickness is the multiplier.
- Ten thousand square feet at 2 inches is 20,000 board feet; at 3.5 inches, 35,000.

**No citable installed spray foam cost exists for this market.**

- Every circulating dollar figure traces to Angi, HomeAdvisor, HomeGuide, or Modernize.
- RSMeans carries city-adjusted national costs behind a subscription, not measured bids.

**Foam selection moves the number before any rate does.**

- Closed-cell publishes an aged R-value of 6.2 to 7.0 per inch, open-cell 3.6 to 4.5.
- The same R with open-cell takes roughly 74 percent more board feet.

**The thermal barrier is where budgets break.**

- Section 2603.4 of the 2021 IBC requires half-inch gypsum wallboard, heavy timber per Section 602.4, or a material meeting NFPA 275.
- The fifteen-minute phrasing is 2006 through 2012 legacy wording; confirm the edition with the AHJ.

**Both states run twenty-year-old energy editions.**

- Kansas names the 2006 IECC under K.S.A. 66-1227 and is home rule, so the decision is local.
- Oklahoma adopted the 2006 IECC with Standard 90.1-2003 effective September 14, 2022.
- Wichita is on the 2024 IBC while the energy side runs a 2006 reference.

If you are budgeting a commercial envelope in Kansas or Oklahoma and you want a bidder who states the installed thickness, converts the job to board feet, puts the thermal barrier on a visible line, and names the code edition and climate zone he priced from, that is how we write scope throughout Texas, Kansas, and Oklahoma. Call me at 512-387-2111 or email ross@bahlfireproofing.com to walk your building and get a scope sheet you can send to every bidder, or [Contact Bahl Fireproofing](https://bahlfireproofing.com/contact/) to start. Our [spray foam insulation](https://bahlfireproofing.com/spray-foam-insulation/) page covers the commercial side of this work, and our [Kansas](https://bahlfireproofing.com/kansas/) page shows where we work in the state.

---

*This article provides general educational information about spray foam insulation, project budgeting, and building envelope requirements. It is not engineering, legal, or code-compliance advice and does not replace project-specific direction from a licensed architect or engineer. Any cost figures and index values are general ranges for illustration only, are not a quote or an estimate, and actual pricing depends on the project, scope, materials, access, and market conditions; obtain a project-specific bid before making any decision. Aged R-value and density are product specific and are revised by manufacturers, so confirm current values against the manufacturer’s latest data sheet. Code citations reference a specific edition and adopted editions vary by jurisdiction, so confirm current requirements with your local building department before specifying or installing.*

Written for Bahl Fireproofing**Ross Bahl, Owner**

Ross owns Bahl Fireproofing, the commercial fireproofing and insulation subcontractor his family started in 1977. Every code figure on this site is checked against the published source before it goes up. [More about Ross](/ross-bahl/).

[PrevPreviousSanctuary Acoustics: The Practical K-13 Ceiling Guide](https://bahlfireproofing.com/sanctuary-acoustics-k-13-worship-centers/)

[NextCore Foam Cost Guide for Commercial Masonry ProjectsNext](https://bahlfireproofing.com/core-fill-cost-commercial-masonry/)

On this page

Bidding this scope?**Send us the drawings.**

Spray-applied fireproofing, intumescent coatings, K-13, spray foam and Core Foam, self-performed across six states. We price the assembly on your drawings, not a square-foot guess.

[Request a bid](/contact/)[Call the office512-387-2111](tel:512-387-2111)

### Have a rated assembly to cover?

Send the drawings and the spec section. We come back with the scope in and the scope out stated plainly, so your bid tab compares the same work across every subcontractor on it.

[Call the office512-387-2111](tel:512-387-2111)[Request a bid](/contact/)

## Keep reading

### [Multi-Family Insulation: The Practical K-13 Guide](https://bahlfireproofing.com/multi-family-insulation-k-13-apartments/)

October 13, 2026

Multi-family developers and property managers call about sprayed insulation for one reason, and that reason is almost always noise. The trouble is

 [Read the guide](https://bahlfireproofing.com/multi-family-insulation-k-13-apartments/)

### [Core Foam Cost Guide for Commercial Masonry Projects](https://bahlfireproofing.com/core-fill-cost-commercial-masonry/)

October 9, 2026

Owners and general contractors budgeting masonry insulation want a number per square foot. No credible published figure exists for Core Foam cost

 [Read the guide](https://bahlfireproofing.com/core-fill-cost-commercial-masonry/)

### [Sanctuary Acoustics: The Practical K-13 Ceiling Guide](https://bahlfireproofing.com/sanctuary-acoustics-k-13-worship-centers/)

October 1, 2026

A sanctuary has to do two things a room is not built to do at once. It has to carry an unamplified

 [Read the guide](https://bahlfireproofing.com/sanctuary-acoustics-k-13-worship-centers/)

```json
{"@context":"https:\/\/schema.org","@graph":[{"@type":"Service","@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/#industry","name":" Fireproofing","url":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/","serviceType":"Commercial Fireproofing","provider":{"@id":"https:\/\/bahlfireproofing.com\/#organization"},"areaServed":[{"@type":"State","name":"Texas"},{"@type":"State","name":"Oklahoma"},{"@type":"State","name":"Kansas"},{"@type":"State","name":"Arizona"},{"@type":"State","name":"Wisconsin"},{"@type":"State","name":"Minnesota"},{"@type":"State","name":"Nebraska"}],"isRelatedTo":[{"@type":"Service","name":"Intumescent Fireproofing","url":"https:\/\/bahlfireproofing.com\/intumescent-fireproofing\/"},{"@type":"Service","name":"Spray-Applied Fireproofing","url":"https:\/\/bahlfireproofing.com\/fireproofing\/"},{"@type":"Service","name":"Cementitious Fireproofing","url":"https:\/\/bahlfireproofing.com\/cementitious-fireproofing\/"}]},{"@type":"BlogPosting","@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/#blogposting","headline":"Spray Foam Cost In Kansas And Oklahoma: 2026 Budget Guide","description":"Spray foam cost has no citable installed price in Kansas or Oklahoma. The real drivers: board feet, foam type, thermal barrier, and the 2006 energy code.","url":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/","datePublished":"2026-10-07T10:00:00-05:00","dateModified":"2026-10-07T10:00:00-05:00","image":{"@type":"ImageObject","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/08\/spray-foam-cost-kansas-oklahoma-hero.webp"},"author":{"@type":"Person","@id":"https:\/\/bahlfireproofing.com\/ross-bahl\/#person","name":"Ross Bahl","url":"https:\/\/bahlfireproofing.com\/ross-bahl\/","jobTitle":"Owner"},"publisher":{"@type":"Organization","@id":"https:\/\/bahlfireproofing.com\/#organization","name":"Bahl Fireproofing, LLC","url":"https:\/\/bahlfireproofing.com\/","logo":{"@type":"ImageObject","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png"}},"mainEntityOfPage":{"@type":"WebPage","@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/"},"articleSection":"Fireproofing","keywords":"commercial fireproofing, SFRM, intumescent","about":[{"@type":"Thing","name":"Commercial Fireproofing"},{"@type":"Thing","name":"Fire-Resistive Construction"}],"name":"Spray Foam Cost In Kansas And Oklahoma: 2026 Budget Guide"},{"@type":["Person","Organization"],"@id":"https:\/\/bahlfireproofing.com\/#person","name":"Bahl Fireproofing","sameAs":["https:\/\/network.procore.com\/p\/bahl-fireproofing-llc-round-rock","https:\/\/subcontractorsaustintexas.com\/company\/bahl-fireproofing-llc\/","https:\/\/www.yelp.com\/biz\/bahl-fireproofing-round-rock","https:\/\/www.buzzfile.com\/business\/Bahl-Fireproofing-LLC-512-387-2111","https:\/\/subcontractorsaustintexas.com\/company\/bahl-fireproofing-llc\/","https:\/\/members.asaonline.com\/directory\/Details\/bahl-fireproofing-llc-2594032","https:\/\/www.osha.gov\/ords\/imis\/establishment.inspection_detail?id=303410971","https:\/\/www.manta.com\/c\/mm70y4c\/bahl-fireproofing-inc","https:\/\/www.nfca-online.org\/index.php?option=com_community&view=profile&userid=2018789809&module=view-all&uuid=f0c1d73b-33e3-4f07-bc9a-acef2520da51&current_page=0&directory_search_id=2006651#\/profile"],"logo":{"@type":"ImageObject","@id":"https:\/\/bahlfireproofing.com\/#logo","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","contentUrl":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","caption":"Bahl Fireproofing","inLanguage":"en-US","width":"312","height":"59"},"image":{"@type":"ImageObject","@id":"https:\/\/bahlfireproofing.com\/#logo","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","contentUrl":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","caption":"Bahl Fireproofing","inLanguage":"en-US","width":"312","height":"59"}},{"@type":"WebSite","@id":"https:\/\/bahlfireproofing.com\/#website","url":"https:\/\/bahlfireproofing.com","name":"Bahl Fireproofing","alternateName":"Bahl Fireproofing LLC","publisher":{"@id":"https:\/\/bahlfireproofing.com\/#person"},"inLanguage":"en-US"},{"@type":"ImageObject","@id":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/08\/spray-foam-cost-kansas-oklahoma-hero.webp","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/08\/spray-foam-cost-kansas-oklahoma-hero.webp","width":"1250","height":"1250","caption":"Spray foam cost: cream closed-cell spray foam on metal wall panels beside bare oxide-red steel where the sprayed area stops","inLanguage":"en-US"},{"@type":"BreadcrumbList","@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":"1","item":{"@id":"https:\/\/bahlfireproofing.com","name":"Home"}},{"@type":"ListItem","position":"2","item":{"@id":"https:\/\/bahlfireproofing.com\/blog\/","name":"Blog"}},{"@type":"ListItem","position":"3","item":{"@id":"https:\/\/bahlfireproofing.com\/category\/fireproofing-blog\/","name":"Fireproofing"}},{"@type":"ListItem","position":"4","item":{"@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/","name":"Spray Foam Cost in Kansas and Oklahoma: A 2026 Budget Guide"}}]},{"@type":"WebPage","@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/#webpage","url":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/","name":"Spray Foam Cost In Kansas And Oklahoma: 2026 Budget Guide","datePublished":"2026-10-07T10:00:00-05:00","dateModified":"2026-10-07T10:00:00-05:00","isPartOf":{"@id":"https:\/\/bahlfireproofing.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/08\/spray-foam-cost-kansas-oklahoma-hero.webp"},"inLanguage":"en-US","breadcrumb":{"@id":"https:\/\/bahlfireproofing.com\/spray-foam-cost-kansas-oklahoma\/#breadcrumb"}}]}
```