---
title: "How To Choose A Fireproofing Contractor: A Buyer's Checklist - Bahl Fireproofing"
description: "Choosing a fireproofing contractor comes down to a few things a general-contractor checklist misses: a manufacturer-approved, factory..."
url: "https://bahlfireproofing.com/how-to-choose-a-fireproofing-contractor-check/"
---

# How to Choose a Fireproofing Contractor: A Buyer’s Checklist

- [Bahl Fireproofing](https://bahlfireproofing.com/author/bahlfireproofing/)
- [July 27, 2026](https://bahlfireproofing.com/2026/07/27/)
- 10:00 am

![C234acdf 44a8 48df b115 5bdbf49a6069](https://bahlfireproofing.com/wp-content/uploads/2026/06/c234acdf-44a8-48df-b115-5bdbf49a6069-1024x1024.png)How to choose a fireproofing contractor: a buyer's checklist 2

Hiring a fireproofing contractor is not like hiring a general contractor or a painter. Fireproofing is a tested, life-safety system, and whether it actually performs and passes inspection depends on the installer’s qualifications and discipline, not on the bid price. This guide walks through what to vet, the credentials that matter, and the red flags that signal a contractor who will cost you more than they save.

**TLDR:** Choosing a fireproofing contractor comes down to a few things a general-contractor checklist misses: a manufacturer-approved, factory-trained applicator, because that maintains the UL listing; the right product and density for the exposure; surface-prep discipline, because bond depends on it; and a contractor who welcomes third-party special inspection instead of treating it as an obstacle. A low bid from an unqualified installer that voids the listing or fails inspection is the expensive option, not the cheap one.

---

Here is the situation that goes wrong. A general contractor or owner takes the cheapest fireproofing bid, the crew sprays, and then the work fails special inspection on thickness, density, or bond. Or the assembly’s UL listing is compromised because the installer was not an approved applicator or used the wrong product. Either way it is now a rip-out and redo, on the critical path, costing far more than the gap between the bids. The worst version passes the paperwork but would not actually protect the steel in a fire. Choosing the right contractor up front avoids all of it, and the things that matter are specific.

## What Should You Look for in a Fireproofing Contractor?

Look for a manufacturer-approved, factory-trained applicator who builds to the specific UL design, uses the correct product and density for the exposure, maintains surface-prep discipline, carries proper insurance and safety compliance, and welcomes third-party special inspection. Credentials like UL Qualified Contractor status or NFCA accreditation signal a contractor who treats fireproofing as the tested system it is.

Those are not the same items you would check for a finish trade, and that is the point. The rest of this guide takes each one in turn, because the difference between a fireproofing job that performs and one that gets torn out usually comes down to these specifics rather than to price or general reputation. It is the same standard we hold ourselves to on every [commercial fireproofing project](https://bahlfireproofing.com/fireproofing/) we install.

## Why Hiring a Fireproofing Contractor Is Different

Fireproofing is a tested life-safety assembly, not a finish. It is installed to a specific UL design, verified by code-mandated special inspection, and its performance in a fire depends on thickness, density, and bond, none of which the eye can judge after the fact. That is what sets it apart from most trades: a coat of paint that is slightly thin is a cosmetic issue, while fireproofing that is slightly thin is a code and safety failure that an inspector will catch or, worse, that a fire will find.

Over the past 20 years bidding and installing commercial fireproofing across Texas, Kansas, and Oklahoma, the projects that go wrong on the contractor almost never go wrong on price. They go wrong because the installer was not approved by the manufacturer, did not build to the specific UL design, skipped the surface prep that bond depends on, or treated the special inspection as an obstacle instead of the check it is. The cheapest bid that leaves those out is the one that gets ripped out and redone, and the savings vanish with the rework.

## Vet the Applicator’s Manufacturer Approval

The single most important credential is manufacturer approval. SFRM and intumescent products are tested and listed as complete systems, and manufacturers qualify and train applicators to install their specific products correctly. Standard specification language requires the installer to be a firm or individual certified, licensed, or otherwise qualified by the fireproofing manufacturer, with trained staff to install the product to the specified requirements. That is not boilerplate. A factory-trained, approved applicator maintains the UL listing of the assembly, while an unapproved installer applying the same product can compromise it.

So the first question to ask any fireproofing contractor is direct: are you an approved or certified applicator for the product specified on this project? Manufacturers such as Isolatek and Carboline maintain applicator networks for exactly this reason, and a contractor who installs a manufacturer’s product without that standing is a risk to the listing you are paying to achieve. If the answer is vague, that is your answer.

## Look for UL Qualified or NFCA Accreditation

Beyond product-specific approval, two industry credentials separate serious fireproofing contractors from general subcontractors who also spray fireproofing. The first is the [UL Qualified Fireproofing Contractor Program](https://www.ul.com/services/ul-qualified-sfrm-contractor-program), a voluntary program in which a contractor is audited against UL’s criteria: appointing a designated responsible individual, passing a recognized industry exam, and maintaining a multi-element quality management system reviewed through an annual audit. Qualified participants can provide a Master Audit Certificate of Compliance for a structure they installed and were audited on.

The second is accreditation through the National Fireproofing Contractors Association. The NFCA’s Contractor Accreditation Program, its education and exams, and its NFCA 100 standard practice for applying SFRM give a contractor a documented standard to work to and to be measured against. Neither credential is legally mandatory, but a contractor who holds one has voluntarily submitted to an audited standard, which tells you something a glossy brochure cannot.

## Confirm They Build to the Specific UL Design

A competent fireproofing contractor works to a UL design number, not a general promise to spray the steel. The UL design specifies the product and the required thickness for each steel shape, and SFRM thickness adjusts according to the size and mass of the member. A contractor who cannot tell you which UL design governs your assemblies, or how they determine thickness for each section, is not estimating the job correctly.

In practice, that means the estimating process should start with your structural and architectural drawings, identify every fire-rated assembly, and determine the required thickness for each steel section from the applicable UL design. That is the difference between a bid built on the listing and a bid built on a square-foot guess. The first holds up at inspection; the second is where the surprises live.

## Demand Surface-Prep Discipline

Bond is everything in fireproofing, and bond starts with the substrate. A good contractor inspects and cleans the steel before spraying, confirms it is free of oil, dirt, loose scale, and incompatible coatings, applies a bonding primer where galvanized or painted surfaces require it, and masks the connections and bolt heads the structural engineer designates. Skipping or rushing that preparation is the most common cause of bond failure, and bond is one of the things the special inspector measures, with adhesion verified per [ASTM E736](https://www.astm.org/Standards/E736.htm).

This is worth probing in conversation, because preparation is invisible in a finished bid. Ask how the contractor handles galvanized or previously painted steel, and how they verify the surface is ready. A contractor who treats prep as a real step, rather than something to spray over, is telling you they understand where fireproofing fails.

## Make Sure They Welcome Special Inspection

On most commercial fireproofing, the building owner engages a third-party special inspector, and that inspector verifies substrate condition, applied thickness, material density, bond and adhesion, and the finished condition under [IBC Chapter 17](https://codes.iccsafe.org/s/IBC2021P1/chapter-17-special-inspections-and-tests/IBC2021P1-Ch17-Sec1705.15). Thickness and density are measured per ASTM E605, bond per ASTM E736, with sampling across the sprayed area. This is not optional on most projects, and it is not the contractor’s job to hire the inspector.

What matters for your selection is the contractor’s attitude toward it. A contractor confident in their work expects the inspection, coordinates with it, and builds the cure time it requires into the schedule. A contractor who resists third-party inspection, downplays it, or seems to hope it will not happen is waving a red flag. The inspection is the check that the work meets the listing, and a good installer wants that check on the record as much as you do.

## Check the Practical Credentials

The standard diligence still applies on top of the fireproofing-specific items. Confirm the contractor carries proper liability insurance and bonding, complies with OSHA safety requirements for the work, and has verifiable commercial fireproofing experience on building types and scopes like yours. References matter here, but the right references: ask for comparable commercial steel projects, not unrelated work. A contractor who has fireproofed warehouses, hospitals, or similar steel structures in your region brings judgment that a generalist does not.

Green flag Red flag

Approved or certified applicator for the specified product Cannot confirm manufacturer approval

Works to a named UL design and explains thickness by member Quotes a flat square-foot number with no listing reference

Treats surface prep as a defined step Vague on prep, galvanized steel, or priming

Welcomes and coordinates third-party special inspection Resists or downplays inspection

References on comparable commercial steel projects References that are residential or unrelated

Matches product and density to the exposure Pushes the cheapest product regardless of environment

## Choosing a Fireproofing Contractor in Texas, Kansas, and Oklahoma

In this region, the right contractor also understands two local realities. The first is that code adoption happens jurisdiction by jurisdiction, so the contractor should know the adopted edition and amendments where the project sits rather than assuming a single statewide rule. The second is climate: Texas heat and humidity affect application windows and cure times, and a contractor who plans around them keeps the schedule and the inspection on track. Verifiable local experience, the credentials above, and a track record on comparable projects are what we built our practice on across our [Texas, Kansas, and Oklahoma service area](https://bahlfireproofing.com/service-areas/). The goal is the same everywhere: a fireproofing contractor whose work performs in a fire and passes inspection the first time.

## Frequently Asked Questions

**What should you look for in a fireproofing contractor?** A manufacturer-approved, factory-trained applicator who builds to the specific UL design, uses the correct product and density for the exposure, maintains surface-prep discipline, carries proper insurance and safety compliance, and welcomes third-party special inspection. Credentials like UL Qualified status or NFCA accreditation reinforce that the contractor treats fireproofing as a tested system.

**Does a fireproofing contractor need to be certified?** There is no single nationwide fireproofing license, but manufacturer approval is critical because an approved applicator maintains the UL listing while an unapproved one can compromise it. Voluntary credentials like the UL Qualified Fireproofing Contractor Program and NFCA accreditation indicate a contractor audited to a documented standard.

**Why is the cheapest fireproofing bid risky?** Because the lowest number often gets there by leaving something out: surface prep, the right product or density, or the scope the code requires. If the work then fails special inspection or compromises the UL listing, the rework cost far exceeds the original savings, putting the project behind on the critical path.

**What is a UL Qualified fireproofing contractor?** It is a contractor who has voluntarily enrolled in UL’s Qualified Fireproofing Contractor Program and been audited against UL’s criteria, including a designated responsible individual, a recognized exam, and an annual-audited quality management system. Qualified participants can provide a Master Audit Certificate of Compliance for structures they installed and were audited on.

**Should I let a third party inspect the fireproofing?** Yes, and on most commercial projects the code requires it. The owner engages a special inspector who verifies substrate, thickness, density, bond, and finished condition under IBC Chapter 17. A good contractor expects and welcomes that inspection and builds the necessary cure time into the schedule.

**How do I know the contractor used the right product?** The product and thickness should match the UL design for each assembly, and the density should suit the exposure. Specifying a lower commercial density in a parking garage or mechanical room to save money, for instance, often leads to damage and rework, so the right contractor matches the product to the environment, not just to the lowest price.

**What questions should I ask a fireproofing contractor?** Ask whether they are an approved applicator for the specified product, which UL design governs your assemblies and how they determine thickness, how they prepare and prime the steel, whether they welcome third-party special inspection, and for references on comparable commercial steel projects. The answers separate a qualified fireproofing contractor from a generalist.

## Key Takeaways

- **Manufacturer approval is the top credential.** A factory-trained, approved applicator maintains the UL listing of the assembly; an unapproved installer can compromise it.
- **Look for audited credentials.** UL Qualified Contractor status and NFCA accreditation show a contractor has submitted to a documented, audited standard.
- **Insist on the UL design.** A real fireproofing contractor works to a UL design number and determines thickness by steel member, not from a flat square-foot rate.
- **Prep determines bond.** Inspecting, cleaning, and priming the steel is where fireproofing succeeds or fails, so a contractor must treat it as a defined step.
- **Welcome the inspector.** Code-mandated special inspection verifies thickness, density, and bond; a confident contractor coordinates with it rather than resisting it.
- **Match product to exposure.** The right density for a parking garage or mechanical room is not the cheapest one, and the wrong choice leads to damage and rework.
- **The cheapest bid is often the most expensive.** A low number that omits prep, the right product, or the required scope ends in failed inspection and rework.

## Related Reading

- General contractor sourcing the work? See our [SFRM buyer’s guide for general contractors](https://bahlfireproofing.com/sfrm-buyers-guide-for-general-contractors/) for the specification side.
- Want to understand the check? Read [the fireproofing inspection process](https://bahlfireproofing.com/the-fireproofing-inspection-process-a-complete-guide-for-building-owners/) for what the special inspector verifies.
- Worried about bond? Our guide to [why surface preparation matters](https://bahlfireproofing.com/why-surface-preparation-matters-in-commercial-fireproofing/) explains where most failures start.

If you are evaluating fireproofing contractors for a commercial project, the work is confirming approved-applicator status, asking which UL design governs the work, pressing on surface prep, and choosing a contractor who welcomes the special inspection. That is the standard we hold on every job throughout Texas, Kansas, and Oklahoma. Reach me directly at 512-387-2111 or [ross@bahlfireproofing.com](mailto:ross@bahlfireproofing.com), or [Contact Bahl Fireproofing](https://bahlfireproofing.com/contact/) to talk through your project with a contractor who works to the listing.

---

*This article provides general educational information on selecting a commercial fireproofing contractor. It is not legal, contractual, or engineering advice, and it does not replace project-specific direction from a licensed architect or engineer. Credential programs, accreditation requirements, licensing, and insurance and bonding standards vary by manufacturer, jurisdiction, and over time, so verify any contractor’s qualifications, licensing, insurance, and references independently before contracting. Code requirements, including special inspection, vary by the authority having jurisdiction. Confirm all requirements with the manufacturer, the building official, and a licensed architect or engineer before proceeding.*

[PrevPreviousSpray Foam for Metal Buildings in Texas: Solving Condensation and Heat](https://bahlfireproofing.com/spray-foam-for-metal-buildings-in-texas/)

[Next5 Signs Your Building’s Fireproofing Needs RepairNext](https://bahlfireproofing.com/5-signs-you-building-fireproofing-need-repair/)

#### Table of Contents

K13 Insulation

### [K-13 Acoustic Performance: NRC Ratings by Thickness](https://bahlfireproofing.com/k-13-acoustic-performance-nrc-ratings/)

K-13’s sound absorption is often quoted as a single number, but that figure hides the two things that actually determine it: how thick the material

 [Read More »](https://bahlfireproofing.com/k-13-acoustic-performance-nrc-ratings/)

Bahl Fireproofing August 4, 2026

K13 Insulation

### [K-13 Color Options and Aesthetic Applications for Exposed Ceilings](https://bahlfireproofing.com/k-13-color-options-and-aesthetic-applications/)

When a design leaves the structure exposed, an open deck, a barrel vault, raw steel and concrete, the ceiling finish has to do two jobs

 [Read More »](https://bahlfireproofing.com/k-13-color-options-and-aesthetic-applications/)

Bahl Fireproofing July 31, 2026

Fireproofing

### [5 Signs Your Building’s Fireproofing Needs Repair](https://bahlfireproofing.com/5-signs-you-building-fireproofing-need-repair/)

The fireproofing on your building’s steel was installed once, at construction, and most owners never think about it again. But it is a physical material,

 [Read More »](https://bahlfireproofing.com/5-signs-you-building-fireproofing-need-repair/)

Bahl Fireproofing July 29, 2026

Fireproofing

### [How to Choose a Fireproofing Contractor: A Buyer’s Checklist](https://bahlfireproofing.com/how-to-choose-a-fireproofing-contractor-check/)

Hiring a fireproofing contractor is not like hiring a general contractor or a painter. Fireproofing is a tested, life-safety system, and whether it actually performs

 [Read More »](https://bahlfireproofing.com/how-to-choose-a-fireproofing-contractor-check/)

Bahl Fireproofing July 27, 2026

Spray Foam Insulation

### [Spray Foam for Metal Buildings in Texas: Solving Condensation and Heat](https://bahlfireproofing.com/spray-foam-for-metal-buildings-in-texas/)

Metal buildings are everywhere in Texas, and they share a problem that standard fiberglass insulation does not fully solve: condensation on cold steel and heat

 [Read More »](https://bahlfireproofing.com/spray-foam-for-metal-buildings-in-texas/)

Bahl Fireproofing July 23, 2026

Spray Foam Insulation

### [When Does Spray Foam Need a Thermal Barrier? IBC 2603 Explained](https://bahlfireproofing.com/when-does-spray-foam-need-a-thermal-barrier/)

Spray foam is an excellent insulator, but the building code does not treat it as just insulation. Because it is a foam plastic, the IBC

 [Read More »](https://bahlfireproofing.com/when-does-spray-foam-need-a-thermal-barrier/)

Bahl Fireproofing July 21, 2026

Spray Foam Insulation

### [Spray Foam Insulation Cost: What Actually Drives the Price](https://bahlfireproofing.com/spray-foam-insulation-cost-what-drive-price/)

There is no single per-square-foot price for commercial spray foam, because the spray foam insulation cost on any given project is driven by a specific

 [Read More »](https://bahlfireproofing.com/spray-foam-insulation-cost-what-drive-price/)

Bahl Fireproofing July 17, 2026

Fireproofing

### [Fireproofing in Hot and Humid Climates: The Texas Challenge](https://bahlfireproofing.com/fireproofing-in-hot-and-humid-climates-texas/)

Fireproofing does not apply and cure the same way on a humid Gulf Coast morning as it does in a dry, climate-controlled lab. In much

 [Read More »](https://bahlfireproofing.com/fireproofing-in-hot-and-humid-climates-texas/)

Bahl Fireproofing July 15, 2026

Fireproofing

### [Texas Fire Code for Commercial Construction: What Actually Governs Your Fireproofing](https://bahlfireproofing.com/texas-fire-code-for-commercial-construction/)

If you are looking for “the Texas fire code” to find out what fireproofing your commercial project needs, the honest answer is that there is

 [Read More »](https://bahlfireproofing.com/texas-fire-code-for-commercial-construction/)

Bahl Fireproofing July 13, 2026

Fireproofing

### [SFRM Special Inspection: What IBC Chapter 17 Requires for Spray Fireproofing](https://bahlfireproofing.com/sfrm-special-inspection-what-ibc-17-requires/)

Spray-applied fireproofing on structural steel is one of the building elements the code singles out for independent, third-party special inspection. This guide explains what IBC

 [Read More »](https://bahlfireproofing.com/sfrm-special-inspection-what-ibc-17-requires/)

Bahl Fireproofing July 9, 2026

```json
{"@context":"https:\/\/schema.org","@graph":[{"@type":"Service","@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/#industry","name":" Fireproofing","url":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/","serviceType":"Commercial Fireproofing","provider":{"@id":"https:\/\/bahlfireproofing.com\/#organization"},"areaServed":[{"@type":"State","name":"Texas"},{"@type":"State","name":"Oklahoma"},{"@type":"State","name":"Kansas"},{"@type":"State","name":"Arizona"},{"@type":"State","name":"Wisconsin"},{"@type":"State","name":"Minnesota"},{"@type":"State","name":"Nebraska"}],"isRelatedTo":[{"@type":"Service","name":"Intumescent Fireproofing","url":"https:\/\/bahlfireproofing.com\/intumescent-fireproofing\/"},{"@type":"Service","name":"Spray-Applied Fireproofing","url":"https:\/\/bahlfireproofing.com\/fireproofing\/"},{"@type":"Service","name":"Cementitious Fireproofing","url":"https:\/\/bahlfireproofing.com\/cementitious-fireproofing\/"}]},{"@type":"BlogPosting","@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/#blogposting","headline":"How To Choose A Fireproofing Contractor: A Buyer's Checklist - Bahl Fireproofing","description":"Choosing a fireproofing contractor comes down to a few things a general-contractor checklist misses: a manufacturer-approved, factory...","url":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/","datePublished":"2026-07-27T10:00:00-05:00","dateModified":"2026-07-27T10:00:00-05:00","image":{"@type":"ImageObject","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/06\/c234acdf-44a8-48df-b115-5bdbf49a6069.png"},"author":{"@id":"https:\/\/bahlfireproofing.com\/ross-bahl\/#person"},"publisher":{"@id":"https:\/\/bahlfireproofing.com\/#organization"},"mainEntityOfPage":{"@type":"WebPage","@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/"},"articleSection":"Fireproofing","keywords":"commercial fireproofing, SFRM, intumescent","about":[{"@type":"Thing","name":"Commercial Fireproofing"},{"@type":"Thing","name":"Fire-Resistive Construction"}],"name":"How To Choose A Fireproofing Contractor: A Buyer's Checklist - Bahl Fireproofing"},{"@type":"BreadcrumbList","@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/#breadcrumb","itemListElement":[{"@type":"ListItem","name":"Home","item":"https:\/\/bahlfireproofing.com\/","position":"1"},{"@type":"ListItem","name":"Blog","item":"https:\/\/bahlfireproofing.com\/blog\/","position":"2"},{"@type":"ListItem","name":"How To Choose A Fireproofing Contractor: A Buyer's Checklist - Bahl Fireproofing","item":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/","position":"3"}]},{"@type":["Person","Organization"],"@id":"https:\/\/bahlfireproofing.com\/#person","name":"Bahl Fireproofing","sameAs":["https:\/\/network.procore.com\/p\/bahl-fireproofing-llc-round-rock","https:\/\/subcontractorsaustintexas.com\/company\/bahl-fireproofing-llc\/","https:\/\/www.yelp.com\/biz\/bahl-fireproofing-round-rock","https:\/\/www.buzzfile.com\/business\/Bahl-Fireproofing-LLC-512-387-2111","https:\/\/subcontractorsaustintexas.com\/company\/bahl-fireproofing-llc\/","https:\/\/members.asaonline.com\/directory\/Details\/bahl-fireproofing-llc-2594032","https:\/\/www.osha.gov\/ords\/imis\/establishment.inspection_detail?id=303410971","https:\/\/www.manta.com\/c\/mm70y4c\/bahl-fireproofing-inc","https:\/\/www.nfca-online.org\/index.php?option=com_community&view=profile&userid=2018789809&module=view-all&uuid=f0c1d73b-33e3-4f07-bc9a-acef2520da51&current_page=0&directory_search_id=2006651#\/profile"],"logo":{"@type":"ImageObject","@id":"https:\/\/bahlfireproofing.com\/#logo","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","contentUrl":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","caption":"Bahl Fireproofing","inLanguage":"en-US","width":"312","height":"59"},"image":{"@type":"ImageObject","@id":"https:\/\/bahlfireproofing.com\/#logo","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","contentUrl":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2025\/02\/7ae06-be6a6e71-7409-4c8c-bc8b-c64bc18f6b39-removebg-preview.png","caption":"Bahl Fireproofing","inLanguage":"en-US","width":"312","height":"59"}},{"@type":"WebSite","@id":"https:\/\/bahlfireproofing.com\/#website","url":"https:\/\/bahlfireproofing.com","name":"Bahl Fireproofing","alternateName":"Bahl Fireproofing LLC","publisher":{"@id":"https:\/\/bahlfireproofing.com\/#person"},"inLanguage":"en-US"},{"@type":"ImageObject","@id":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/06\/c234acdf-44a8-48df-b115-5bdbf49a6069.png","url":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/06\/c234acdf-44a8-48df-b115-5bdbf49a6069.png","width":"2048","height":"2048","caption":"How to Choose a Fireproofing Contractor: A Buyer's Checklist","inLanguage":"en-US"},{"@type":"BreadcrumbList","@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":"1","item":{"@id":"https:\/\/bahlfireproofing.com","name":"Home"}},{"@type":"ListItem","position":"2","item":{"@id":"https:\/\/bahlfireproofing.com\/blog\/","name":"Blog"}},{"@type":"ListItem","position":"3","item":{"@id":"https:\/\/bahlfireproofing.com\/category\/fireproofing-blog\/","name":"Fireproofing"}},{"@type":"ListItem","position":"4","item":{"@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/","name":"How to Choose a Fireproofing Contractor: A Buyer’s Checklist"}}]},{"@type":"WebPage","@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/#webpage","url":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/","name":"How To Choose A Fireproofing Contractor: A Buyer's Checklist - Bahl Fireproofing","datePublished":"2026-07-27T10:00:00-05:00","dateModified":"2026-07-27T10:00:00-05:00","isPartOf":{"@id":"https:\/\/bahlfireproofing.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/bahlfireproofing.com\/wp-content\/uploads\/2026\/06\/c234acdf-44a8-48df-b115-5bdbf49a6069.png"},"inLanguage":"en-US","breadcrumb":{"@id":"https:\/\/bahlfireproofing.com\/how-to-choose-a-fireproofing-contractor-check\/#breadcrumb"}}]}
```